电信手持设备

Standards, compatibility and design

电信手持设备

Several design challenges exist when designing audio for a telecom handsets. These include:

Frequency response (receiving audio) must pass type approval
Leak tolerance (consistent bass response)
Hearing Aid Compatibility (HAC)
Microphone (transmitting audio) must pass type approval
Chosing loudspeaker for hands-free audio

Target response and standards

For telecom handsets to be type approved, certain performance criteria must be met. The handset’s frequency response (receive) must be measured on a standardized artificial ear, which basically is an acoustical copy of the human ear designed with a controlled leakage. The frequency response must lie within a certain “window” defined in the standard. The same goes for the outgoing sound (send) which also has to meet certain frequency response criteria defined in the standards. Examples of such windows are shown below.

Super Wideband gaining pace

The share of telecom handsets that comply with the Super Wideband standard is growing, which requires receivers with high technical performance as well as it increases the design complexity of the handsets.

Super Wideband	ITU-T	P1120
Wideband	IEC	TIA920A
Wideband	ITU-T	P.311
Narrowband	IEC	TIA810B

Ole Wolff has the test eqiupment, tools and experience neccessary to design handset that comply with all of the telecom standards.

Receive frequency response and limits.

Send frequency response and limits.

Consistent bass response (leak tolerance)

When holding a handset close to the ear there will always be an acoustic leakage formed between handset and the ear. If the receiver was ideal (large sized membrane & motor), such leakage would not degrade the sound quality. In most modern handsets the performance of the incoming audio has shifted from being handled by the transducer alone to involve acoustical access to the internal part of the handset. This is due to the fact that handsets are getting smaller and smaller which calls for smaller components, including the receiver (driver) producing the sound. However, shrinking the receivers size will have a huge impact on the sound reproduction capability easpecially in the bass region if no modifications are done.

The solution is to use a receiver designed to have a huge bass boost and introduce a controlled leakage between the front of the receiver to the outer free field or alternatively to the inside of the handset (rear side of the driver). The result will be that the huge initial bass boost will be loaded down to a flat response, which then can accept an additional leakage between handset and ear without any significant loss of bass content. This design however is not not straght forward and involves controlling acoustic resistances, masses and volumes using slits, tubes, cavities and fabric (damping).

Example of frequency response of handset without leak tolerance when held firmly to the ear (solid) and when moved just a few milimeters away from the ear (dashed). A leak tolerant design would only loose a few dB’s and thus be similar to the solid curve in both situations resulting in a much more consistent (pleasant) LF reproduction.

The leakage path can be built into the handset using carefully dimensioned tubes and acoustic fabric.

The OWR-3083 receiver has built-in leakage which can simplify the acoustic design of the handset.

Hearing aid compatability (HAC)

Hearing Aid Compatibility (HAC) is a property of the handset where a magnetic field mirroring the audio signal is distributed from the ear cap plane of the handset and picked up by a coil positioned in a hearing aid worn by the phone user. The hearing aid will then transform the magnetic signal into an acoustic signal with the applied corrections needed for the user. Typically the hearing aid will turn off its microphone when a HAC signal is detected and thus there will be no “acoustics” between the senders outgoing signal and the signal reaching the hearing aid. For the hearing impaired this technique can increase the percieved sound quality considerably.

In most cases the receiver unit will produce this magnetic signal using its built-in voice coil. Alternatively an external tele coil can be built into the handset if the receiver cannot generate the required magnetic signal strength on its own. Receivers having HAC compatibility are typically designed to have a “high” current coil for keeping up a high magnetic signal as well as a high acoustic signal.

DSP is not the answer

It is important that the receiver’s frequency response (in the HAC window) is acoustically well balanced since drastic DSP corrections would also affect the HAC signal.

Often the handset is placed on top of the hearing aid to ensure the best pickup of the magnetic signal.

HAC limits and standards

To make a handset HAC compatible, it must comply with telecom standards. An example of a narrow band HAC frequency window is shown to the right.

麦克风

Typically space is not limited in the bottom area of the handset where the microphone is positioned. The microphones are typically electrete microphones in the size range of Ø6mm to Ø10mm which are low cost “work horses” with great performance. If space is limited, a much smaller MEMS microphone is the ideal choice.

For both microphone types the HF response can be tuned by the front cavity and sound inlet in the handset, forming an acoustic low pass filter. Sometimes a front resonance at, say, 10 kHz can be designed into the handset to boost the response in that frequency range. The microphone response (send) must also comply with standards as described in the section “Target response and standards” above.

Simulations of handsets

Using Comsol Multiphysics™ Ole Wolff can simulate all of the acoustics involved when designing a telecom handset. We use accurate models of artificial ears for comparing simulation results with experimental data. Typically we do “virtual prototypes” in close cooperation with the customer’s design team. In this way the tranducers, acoustic chambers etc. can be modified and changed without ever having to build physical prototypes. Once the simulation results show that performance targets are met, samples are built and tested in the lab.

Simulated frequency response of a 8x15mm receiver built into a handset with leak tolerance.

Normalized simulated frequency response of pressure on MEMS microphone using three different types of acoustic fabric to lower resonance peak at 4 kHz.

了解有关 Comsol Multiphysics 仿真的更多信息

Measuring the real deal

The labs at Ole Wolff are equipped to measure all of the parameters necessary to verify that the handset complies with all of the telecom standards. We use artificial ears, HAC probes KEMAR dummy head with mechanical “hand”, and ear & mouth simulator. The performance of the raw drivers are verified using Klippel™ systems, Listen SoundCheck™ and more. For hands-free audio the performance can be verified in anechoic chambers or by using Klippel™ SCN Near Field Add-on.